Pottery Supplies Online

Earthenware Clear Super Gloss Glaze Powder Glaze 1040-1220ºC (B5381)

Earthenware Clear Super Gloss Glaze Powder.
Firing Range 1040-1220ºC
AUD$ 16.35
Select Option
Choose a variant

Powder Glaze - Lead Free - Australian Made and supported
Setting up a glaze from powder for Dipping or Spraying
Wearing a suitable mask, sprinkle the glaze powder into a suitable container of water and stir thoroughly. Leave to settle overnight and pour off surplus water. Stir, sieve through an 80 mesh or finer sieve, then add water if necessary to achieve the desired consistency. This depends upon the porosity of the bisque ware but will be around 500-700 gm of powder to 570 ml of water. When some liquid glazes settle out, particularly over a long period of time, they sometimes set hard at the bottom of the container, making them difficult to re-mix. Others may settle during use and consequently demand thorough stirring or agitation during the dipping session. To correct this defect, a flocculent or anti-set solution should be added a little at a time, stirring it in very well until the settling stops. Add carefully or the glaze will dry slowly on the ware and may cause mud cracking and perhaps crawling during firing. The opposite effect of settling is when the glaze appears like thin custard and has a creamy feel. The glaze dries slowly on the ware or peels off during drying. Some glazes that have a high clay content, or raw zinc oxide, magnesium carbonate, talc, etc., or have had excess dosing of anti-set will have this defect. The cure is to add very cautiously, small quantities of a 10% solution of Soda Ash or Sodium Silicate, stirring well, until normal drying and behaviour occurs. APPLICATION OF PREPARED GLAZE
Use either a bucket or glaze wok. The type of glaze and the effect desired will indicate how the ware should be dipped: transparent glazes should be thinner than opaque ones so dip once only. A rutile glaze may be dipped once or twice for varying colour effects. 
Walker Ceramics dipping glazes are delivered with a litre weight of 1500-1750 grams/litre (Specific Gravity (SG) of 1.5-1.75) depending on glaze composition. 
Adjusting the glaze to a slip suitable for individual preferences requires the following: 
Essential: Dispex, Epsom Salts, volume measuring container, scale with 1 gm tolerance. 
Optional : Ford Cup #4 or Paint viscometer, stop watch. 
Adjust the litre weight to between 1400-1500 gm/litre (Specific Gravity of 1.4 1.5) by adding clean tap water to the slip. 
The glaze slip should have the viscosity of evaporated milk or slightly higher. 
If glaze slip is too thick, add Dispex (Product Code CB80) drop by drop until viscosity is satisfactory. 
Never add water once you have Specific Gravity correctly adjusted!! 
If glaze slip is too thin, add Epsom Salts solution drop by drop until viscosity is correct. 
(To make Epsom Salts solution, mix 300 gm of Epsom Salts with 1 litre of hot water.) 
It is highly recommended to use a Ford Cup or Viscosity Cup and aim for run-out time of 15 to 20 seconds. 
After application the glaze layer should be as thick as the diameter of a standard steel paper clip. 

Search and Filter

Our Location

We are conveniently located directly across the road from the Suncorp Stadium.
Come down and say hello.
Order online or click and collect

Address: 51 Castlemaine Street, Milton, QLD
Phone: (07) 3368 2877

Opening Hours

Monday: 9 am–4:30 pm
Tuesday: 9 am–4:30 pm
Wednesday: 9 am–4:30 pm
Thursday: 9 am–4:30 pm
Friday: 9 am–4:30 pm
Saturday: 9 am–12 pm
Sunday: Closed

Closed Public Holidays 

Contact Us

Call: +61 07 3368 2877

51 Castlemaine Street,